Home  

Performance engines

All performance engines are built with new parts and are zero mile units, no exchange unit required.

I am constantly working to provide the best quality engine possible with outstanding

performance and reliability. All my engines are hot run for 30 min to break in the camshaft.

I pride myself on offering the best service possible.

If you have any questions on the engines below please call  on

Tel 01159 301242 (9am - 5pm) or Mob 07852 186023 (9am - 7pm) 

1776 cc  Stage 2.    2270.00 pounds sterling    

 

This is by far the most popular of my engines. If fitted with twin single choke Webers (34 ICTs) it will give 95 bhp*+ with SCAT C25 cam and approximately 30 mpg in an early T2. When Fitted with twin, twin choke Webers (40s), it will give slightly better performance at the top end of the rev range, but with some loss of performance at the bottom end and a slight reduction in economy.  Higher output can be achieved with a wilder cam.

 
  •  brand new aluminium case
  • new 69mm crankshaft
  • new lightened forged flywheel 
  • new clutch
  • 8 dowel flywheel to crankshaft
  • chromoly gland nut 
  • crank shaft assembly dynamically balanced
  • performance camshaft, followers, spring, collars and retainers  (scat c25)
  • double thrust cam bearings
  • new chromoly I-beam con rods  
  • con rods and pistons balanced separately to within 1 gram
  • mahle 90.5mm barrels & pistons 
  • teflon buttons 
  • Heavy duty Scat push rods
  • new cb performance 044 heads with 3 angle valve seat 
  • Increased compression ratio
  • Bolt up rocker shaft
  • new 1.25 ratio rockers 
  • scat swivel feet adjusters 
  • new 30mm geared oil pump 
  • remote filter system (except hoses you supply crimped)
  • gaskets to fit ancillaries
  • when bought with carbs i will match manifolds to heads
  • when fitted with twin single choke Weber carburettors will give 95 bhp* +

Upgrade above engine to a 69mm counter weighed crankshaft,

for onle 70 pounds sterling

 

1915 cc  Stage 3.    2570 pounds sterling

If fitted with twin, twin choke Webers (40s), this engine will give excellent performance across the rev range with a peak of 125 bhp @4800rpm using a SCAT C35 cam*.  

As 1776 Stage 2 plus
  • new aluminium super case 
  • 69mm counter weighed crankshaft
  • 2 litre deep sump
  • scat  C25 or C35 cam
  • 94 mm barels and pistons
  • CB 044  big valve heads (exhaust valves 35.5 mm, inlet valves 40 mm)

 

2276 cc  stage 3.    2770 pounds sterling
  • this includes the use of a aluminium supercase
  • kennedy stage 1 pressure plate
  • forged 82mm stroke crank
  • chromoly  H-beam rods

  

Carburettor choice

All carburettors are pre-jetted to suit your engine.  Please note that fitting carburettors which are too large

will not necessarily greatly improve performance but may increases the fuel consumption.

Optional items
twin single-choke Weber carburettors 34 ICTs, c/w manifolds, linkages, filters and gaskets, jetted to suit your engine and fitted 450

 

 

twin twin-choke Weber carburettors 44 idf, complete kit, c/w manifolds, linkages, filters and gaskets, jetted to suit your engine and fitted

650

port work on heads T1 or T4 (adds about 10 to 15 % more power) cost per pair 325

            ancillary pack   

  • spec coming soon
 
 
 

* Please note bhp figures may vary depending on the rolling road!

 

all prices are subject to change at any time

due to the strength of the pound